Our Products
Showing 1-24 of 41 products
Forged Steel Globe Valve, Class-800 (Standard Bore))
Design Standard API 602 / BS EN ISO 15761 (BS 5352).
Body and Bonnet are Phosphated, to ensure maximum resistance from rust.
Bolted Bonnet, Outside Screw, Yoke Type, Rising Stem.
Screwed Female Ends to BSPT / NPT / Socket Welded to ANSI B16.11.
Tile
Cast Iron Dual Plate Wafer Type Check Valve, PN 16
Design standard API 594.
Wafer Type Design, to take lesser space than the conventional Check Valve.
Being light in weight, is more rigid than the standard Swing Type Check Valve, which needs expensive foundation and special supports.
Being cylindrical body, stresses are uniformly distributed.
Much longer seat life because of Bronze / S.S to Rubber contact.
Less wear and tear of seat surfaces.
End connections are designed to suit flanges drilled to ANSI B Class-125 / ASME B Class-150.
Water hammering effect is minimized in this design, since the closing of valve does not depend upon any back pressure or flow.
Each plate being half of the size of the swing check valve disc, provides straight flow path offering minimal resistance because of the spring’s assistance as closing of the valve initiates as soon as flow velocity dips below the designated minimum velocity.
Forged Brass Ball Valve (Screwed)
Screwed Female Ends to IS 554 / BS 21 / ISO 7.
Full Bore, Two Piece Design.
Quarter Turn, Lever Operated.
Provided with Forged Brass Hard Chrome Plated Ball.
Premium Quality PTFE Gland Packing and Seating.
Chrome Finish.
By pass check valve
Design Standard IS 5312 – 1.
Flanged Ends to IS 1538.
Seating design – Swing Type.
Bolted Cover.
Renewable Seat with Premium Quality Rubber Flap.
Flexible installation (Horizontal / Vertical)
1 Bolts Carbon Steel IS 1363 Part 1 Class 4.6
As Reqd.
2 Cover Cast Iron IS 210 Gr. FG 200 1
3 Gasket Nitrile Rubber IS 638 Type B 1
4 Body Cast Iron IS 210 Gr. FG 200 1
5 Hinge Pin Stainless Steel IS 6603 Gr. X04 Cr19Ni9 1
6 Body Seat Ring Bronze IS 318 Gr. LTB 2 1
7 Bolts Carbon Steel IS 1363 Part 1 Class 4.6 1
8 Washer Carbon Steel – – – 1
9 Disc Facing Nitrile Rubber IS 638 Type B 1
9 Disc Facing Nitrile Rubber IS 638 Type B 1
10 Disc Cast Iron IS 210 Gr. FG 200 1
11 Hinge Cast Iron IS 210 Gr. FG 200 1
1083C 1083Csizes
Bronze globe valves screwed
Screwed Female Ends to BSPT.
Straight Pattern, Screwed in Bonnet, Inside Screw, Rising Stem.
Provision for re-packing under pressure.
Handwheel Operated.
Premium Quality lubricated Gland Packing.
Renewable 13% Cr. Stainless Steel (S.S 410) working parts.
Stainless Steel Thermodynamic Steam Trap (Screwed)
Screwed Female Ends to BSPT.
Superior Quality Investment Casting.
Provided with integral strainer.
Stainless Steel (S.S 304) 0.5 mm hole diameter perforated sheet screen for trouble free service.
Mirror finished moving disc.
1080B Stainless Steel (CF8M / S.S 316) Three Piece Design Ball Valve, Class-150 (Flanged)
1077 Cast Steel Gate Valve, Class-150 (Flanged)
Design Standard BS EN ISO 10434 / API 600.
Bolted Bonnet, Outside Screw, Yoke Type, Rising Stem.
Renewable 13% Cr. Stainless Steel (S.S 410) working parts.
Handwheel Operated.
Flanged Ends as per ASME B 16.5 Class-150.
1078K Butterfly Valve (Wafer Type), PN 1.6 with Electrical Actuator
1087A Cast Iron Double Regulating Balancing Valve (Flanged) With Nozzle
1087A Cast Iron Double Regulating Balancing Valve (Flanged) With Nozzle
Salient Features
Design Standard BS 7350.
Precise double regulation.
Tamper proof setting.
Handwheel Operated.
Low noise flow.
Can be made available with or without drain cocks.
Flanged ends to BS 4504 Section 3.2 PN 16.
EPDM Rubber sealing for a soft shut off.
Pneumatic butterfly valve
Landing valve (fire hydrant valve)
Design Standard IS 5290.
Confirming to Type A specification.
Screwed in Bonnet having instantaneous coupling with single outlet.
PTFE Gland Packing for longer life and smooth operation of stem.
Large flow way area to get full flow of water.
Leakage proof by virtue of elastomer seat.
Smooth operation of blank cap for quick mounting of water pipe.
Screwed in Bonnet having instantaneous coupling with single outlet.
PTFE Gland Packing for longer life and smooth operation of stem.
Large flow way area to get full flow of water.
Leakage proof by virtue of elastomer seat.
Smooth operation of blank cap for quick mounting of water pipe.
Life long rust free service.
1 Body Stainless Steel IS 3444 Gr. 1 1
2 Chain Carbon Steel – – – 1
3 Disc Nylock Nut Carbon Steel – – – 1
4 Washer Stainless Steel IS 6603 Gr. X04Cr19Ni9 1
Cast Steel Globe Steam Stop Valve (Flanged)
Flanged Ends to DIN 2545 PN 40.
Straight Pattern, Outside Screw, Yoke Type, Rising Stem, Bolted Bonnet.
Renewable 13% Cr. Stainless Steel (S.S 410) working parts.
Minimum pressure drop inside the body due to streamlined body design.
Handwheel Operated.
Provision for re-packing under pressure.
Suitable for thermic fluid application also.
Cast Iron Y-Type Strainer PN 10 (Flanged)
Flanged Ends to BS 10 Table ‘F’.
Stainless Steel (S.S 304) perforated sheet screen (Ø3 mm Perforation) is guided in body and cover.
Large screening area makes the strainer efficient in performance.
Minimum pressure drop inside the body due to streamlined body contours.
Bronze Vertical Check Valve (Screwed)
Screwed Female Ends to IS 554 / BS 21 / ISO 7.
Single Piece Design, Integral Seat.
Meant for Vertical Lines Only.
Permits flow in one direction and shuts automatically if the flow reverses.
Spring Loaded and ‘O’ Ring Type.
Also available with metal to metal seating.
Stainless Steel (CF8M / S.S 316) Three Piece Design Ball Valve, Class-150 (Screwed) Article Code 1080A
Design Standard BS EN ISO 17292 (BS 5351).
Screwed Female Ends to BSPT / NPT / Socket Weld.
Reduced Bore, Three Piece Design.
Superb in Quality and Performance.
Cast Steel Parallel Slide Blow Off Valve (Flanged)
Flanged Ends to BS 10 Table ‘J’.
Maintains fluid tightness and is easy in operation because of sliding action of discs.
Discs are kept in close contact with body rings by means of a spring when the valve is under pressure.
Premium Quality lubricated Gland Packing, Bolted Bonnet.
Valve is operated by means of Rack and Pinion arrangement, in such a manner that valve is opened fully with half turn of the box key.
Gland forms a locking guard which prevents removal of the key unless the valve is closed.
Bronze Double Regulating Balancing Valve (Screwed) With Nozzle
Design Standard BS 7350.
Precise double regulation.
Tamper proof setting with a lock shield.
PTFE sealing disc to ensure a proper shut off.
Provided with Inlet / Outlet pressure test cocks.
Facilitates system design, hence saves energy.
Handwheel Operated.
Easy to install and set.
Accentuates systematic commissioning of the plant for an optimal operation.
Butterfly Valve (Wafer Type) PN 1.6 with S.G Iron Disc
Design Standard IS 13095 / BS EN 593 (BS 5155).
Wafer Type.
Lever Operated.
S.G Iron construction.
S.G Iron disc which is accurately guided between the two stems.
Integrally moulded rubber lining (EPDM / Nitrile / Neoprene* / Viton* / Silicon*) as per requirement which provides seating to the valve disc, as a primary seal to the stem and gasket joint with matching pipe flanges.
Two Piece Stem design which is precisely guided between the PTFE / Bronze bushes.
Compatible to sandwich between flanges as per BS 10 Table D, E, F,H, DIN, PN 10, PN 16, PN 25, PN 40, ASA 150, ASA 300, IS 778, IS 6392 Table 17 and IS 1538.
*Valves with Neoprene / Viton / Silicon lining can also be provided at nominal extra cost.
Butterfly Valve (Wafer Type), PN 2.5 with S.G Iron Disc - Gear Operated
Design Standard IS 13095 / BS EN 593 (BS 5155).
Wafer Type.
Gear Operated.
S.G Iron construction.
S.G Iron disc which is accurately guided between the two stems.
Integrally moulded rubber lining (EPDM / Nitrile / Neoprene* / Viton* / Silicon*) as per requirement which provides seating to the valve disc, as a primary seal to the stem and gasket joint with matching pipe flanges.
Two Piece Stem design which is precisely guided between the PTFE / Bronze bushes.
Compatible to sandwich between flanges as per BS 10 Table D, E, F,H, DIN, PN 10, PN 16, PN 25, PN 40, ASA 150, ASA 300, IS 778, IS 6392 Table 17 and IS 1538.
*Valves with Neoprene / Viton / Silicon lining can also be provided at nominal extr
Product Name Butterfly Valve (Wafer Type), PN 2.5 with S.S 304 Disc - Gear Operated
Design Standard IS 13095 / BS EN 593 (BS 5155).
Wafer Type.
Gear Operated.
S.G Iron construction.
Stainless Steel (CF8 / CF8M*) Disc which is accurately guided between the two stems.
Integrally moulded rubber lining (EPDM / Nitrile / Neoprene* / Viton* / Silicon*) as per requirement which provides seating to the valve disc, as a primary seal to the stem and gasket joint with matching pipe flanges.
Two Piece Stem design which is precisely guided between the PTFE / Bronze bushes.
Compatible to sandwich between flanges as per BS 10 Table D, E, F,H, DIN, PN 10, PN 16, PN 25, PN 40, ASA 150, ASA 300, IS 778, IS 6392 Table 17 and IS 1538.
*Valves with Neoprene / Viton / Silicon lining and CF8M (S.S 316) Disc can also be provided at nominal extra cost
Forged Steel Horizontal Lift Check Valve, Class-800 (Standard Bore)
Design Standard API 602/BS EN ISO 15761 (BS 5352).
Body and Cover are Phosphated, to ensure maximum protection from rust.
Bolted Cover.
Screwed Female Ends to BSPT / NPT / Socket Welded to ANSI B16.11.
Cast Steel Horizontal Lift Check Valve (Flanged)
Flanged Ends to DIN 2545 PN 40.
Bolted Cover, Straight Pattern.
Renewable 13% Cr. Stainless Steel (S.S 410) working parts.
Minimum pressure drop inside the body due to well contoured body design.
Suitable for thermic fluid application also.
